| Technical Training Group Course Listing On-line Registration Welcome to the course listing and on-line registration page. To view a course description just click on the name of the course. To view a course schedule or to register for a course click on schedule/register. Most of the courses are bundled as a 2 day combo. You can attend both days or an individual day by making the appropriate selection. |
||||||
| Medium Voltage Power Systems | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU's - Typically operating at voltages ranging from 2,400 to 34,500 Volts, medium voltage power systems present special challenges such as voltage stress, corona, surges and equipment protection. Achieve a better understanding of medium voltage power systems and the unique problems. | ||||||
| How to Perform an Arc Flash Study - I | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEUs - Implementing an Electrical Safety Program? Just what are the requirements? This class discusses OSHA and NFPA 70E requirements to determine what is required to comply. Day 1 is designed to provide an understanding of electrical safety including performing a shock and arc flash hazards analysis as required by NFPA 70E. Learn how to determine flash boundaries based on the 4 foot rule and using calculations based on NFPA 70E. See how to use Table 130.7(C)(9)(a) Hazard/Risk Category Classification for selecting Personal Protective Equipment. Also learn how to determine the limited, restricted and prohibited approach boundaries and properly use Energized Work Permits. | ||||||
| How to Perform an Arc Flash Study - II | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEUs - Taking arc flash studies to the next level? This course shows you how to perform the detailed arc flash study based in IEEE 1584 methods for performing arc flash calculations. Learn how to calculate arcing short circuit current, incident energy and flash protection boundaries. There are many in class arc flash problems to solve during the course. Jim provides Arc Flash calculation worksheets in the class to assist in the problem solving. These worksheets are also found in his “Guide for Arc Flash Calculations” found at www.brainfiller.com. Learn the significance of grounded vs. ungrounded systems on incident energy as well as the X distance factor, gap spacing, arc in a box vs. in air and many other important factors. Learn about whether to cut off device clearing times at 2 seconds and whether to take the calculations below 125 kVA 208V transformers. Jim Phillips takes you beyond the standard arc flash discussions and also talks candidly about holes in the standards, future research and common interpretations. He also will show you how to simplify the electrical safety program to minimize confusion. | ||||||
| How to Perform an Arc Flash Study I and II | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Day - 1.6 CEUs - This 2 day program is the course that many instructors from other training companies have attended to see how it is done. This program combines Day 1 and Day 2 to provide a comprehensive training program for a complete understanding of arc flash hazards, electrical safety and performing the complete arc flash study based on IEEE 1584. As a member of the IEEE 1584 Working Group, Jim Phillips, covers it all with this program. THIS COURSE IS AVAILABLE ON DVD. | ||||||
| One Week Power System Engineering Course - (5 Days ) | $1095.00 | Schedule/Register | ||||
| This one week class is a combination of our five most poplular courses rolled into one week long program. The five courses include: Design of Electric Power Systems I and II, Short Circuit Analysis, Protective Device Coordination Analysis and Harmonic Analysis. The class is held several times in 2007 including Canton, OH - Scottsdale, AZ - and Orlando, FL. For a detailed agenda of the one week class, please view each individual course's agenda in the course listing or the description on the home page of the website. This class usually fills up early so register quickly to make sure you have a seat. Rememeber, send 3 people and the 4th is free! 3.2 CEU's (32 Class Hours) |
||||||
| Generator and UPS Applications | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEUs - With electric utility deregulation and decreasing reliability, on-site generation is more important than ever. Whether used for emergency power systems, peak shaving, or co-generation, learn the requirements of sizing, selection, operation and planning a generator installation. Included is how to analyze the effect of harmonic loads and motor starting as well as generator - UPS compatibility issues. Understand the impact of NEC 700.27 Coordination. You will also learn how to size and select UPS systems for mission critical designs. | ||||||
| EasyPower Smart Design | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.5 CEUs - Learn how to save time and money by using EasyPower’s SmartDesignTM software to automatically design low voltage electrical power systems. This 2 day workshop will show you how to automatically size and select equipment based on National Electrical Code® requirements. Develop a one line drawing and learn how to use SmartDesignTM for sizing panels, motor control centers, switchboards, switchgear, overcurrent devices and feeders as well as develop load calculations and equipment schedules. Then produce a bill of material and cost estimate automatically, export your design documents to AutoCAD® and Your Done! | ||||||
| Power Distribution Equipment - I | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU's - Power Distribution Equipment - I and its companion course Power Distribution Equipment - II contain many examples and problems relating to the selection and application of equipment. The course provides valuable insight into the operation, selection and application of motors and variable frequency drives. You will also learn about transformer design application, protection as well as transformer vault requirements. | ||||||
| Power Distribution Equipment - II | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU's - Power Distribution Equipment - II and its companion course Power Distribution Equipment - I contain many examples and problems relating to the selection and application of equipment. The class includes the application and selection of circuit breakers, switchboards, fuses, and relays. In addition, low & medium voltage switchgear and an introduction to short circuit and coordination studies is included. You will be drawing time current curves. | ||||||
| Power Distribution Equipment I and II Combo | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU's - This 2 day course is a combination of both Power Distribution Equipment I and Power Distribution Equipment II. | ||||||
| Short Circuit Analysis | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This course is presently available as part of the One Week Power System Engineering Course held several times a year. The course is also available as an on-site program at your location. This course is designed to show you how to perform short circuit calculations and perform equipment evaluation. Many calculation examples are used to illustrate how to perform an analysis. The methods are based on the IEEE Buff and Red books. AVAILABLE AS A SELF STUDY PROGRAM | ||||||
| Protective Device Coordination Analysis | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This course is presently available as part of the One Week Power System Engineering Course held several times a year. The course is also available as an on-site program at your location. This course is designed to show you the concepts of time current curves and coordination studies. The program provides an explanation of how time current curves are to be used and how to maximize reliability by developing a properly coordinated power distribution system. AVAILABLE ON DVD | ||||||
| Short Circuit and Coordination Combo | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU'S - This class is available as part of the "One Week Power System Engineering Course" found in this course listing. | ||||||
| Grounding and Power Quality | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S Many power quality problems can be traced to poor or incorrect grounding. This course takes you through the correct grounding requirements as well as an in depth look at power quality problems. | ||||||
| Harmonic Analysis and Power Factor | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S Harmonics can cause substantial overheating and damage on power systems. This course shows you how to analyze harmonics and the impact of power factor correction capacitors on resonance. | ||||||
| Grounding/Power Quality and Harmonics Combo | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| Only the Harmonic Analysis and Power Factor class is presently scheduled as part of the "One Week Power System Engineering Course" found in this course listing. | ||||||
| How to Streamline and Automate Electric Power System Design | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU's - In today's business climate, it is essential to work faster, smarter and more efficient to stay competitive. This class not only teaches you power system design, it also shows you how to streamline and automate much of the design process to give you a competitive edge! | ||||||
| Design of Electric Power Systems - I | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This class is available as part of the "One Week Power System Engineering Course" The course takes you from electrial design basics to practical design problems. | ||||||
| Design of Electric Power Systems - II | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This class is available as part of the "One Week Power System Engineering Course". The course includes designing transformer and motor circuits, grounding, hazardous locations and more. | ||||||
| Design of Electric Power Systems I and II Combo | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU'S - This class is available as part of the "One Week Power System Engineering Course" and is made up of both Design I and Design II courses. | ||||||
| Protective Relaying - I | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEUs - Learn the fundamentals of overcurrent relaying with this class. You will be using time-current curves to determine appropriate relay settings including the Amp Tap, Time Dial and Instantaneous. See how to evaluate current transformer saturation and burden. | ||||||
| Protective Relaying - II | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEUs - Expanding on day 1, this class introduces directional relays and various protection schemes. Learn how to protect transformers using ANSI C57 thru-fault curves. See how to set transformer differential relays and how to protect motors and generators. | ||||||
| Protective Relaying I and II | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEUs - The 2 day package combines both Day 1 and Day 2 courses. Learn how to set many types of relays. | ||||||
| National Electrical Code (c) - 2 Days | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU'S - This 2 Day course shows you how to use the major articles of the National Electrical Code. We not only look at code articles but also how to apply the articles with examples and also a behind the scenes on why some of the articles were created. | ||||||
| Fundamentals of Electric Power Calculations I | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This course introduces the per unit system that is used in the power system analysis world. There are many detailed problems to solve in class. | ||||||
| Fundamentals of Electric Power Calculations II | $350.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 1 Day - 0.8 CEU'S This course is a continuation of the first course and shows you how to use symmetrical components in problem solving. | ||||||
| Fundamentals of Electric Power Calculations I and II Combo | $695.00 |
Not Presently Scheduled Available as an In-House Training Program |
||||
| 2 Days - 1.6 CEU'S - This 2 Day course is a combination of both days. It is presently available as an on-site program. This course makes an excellent P.E. Exam review. | ||||||
